LDG Automatic Tuners

The AT-200Pro Tuner:

• 5 to 250 watts SSB and CW. (100 watts on 6M)
• Easy to read LED bargraph display for RF power, SWR and status
• 16,000 3D memories for instantaneous band changing
• Two position antenna switch with memories for four antennas on each position
• Tuning time: 0.5 to 6 seconds full tune, < 0.1 second memory tune
• Built in frequency counter for memory operation
• Frequency coverage: 1.8 to 54.0 MHz.
• Tunes 6 to 1000 ohm loads (16 to 150 ohms on 6M)
• Tunes 6 to 4000 ohms with optional 4:1 Balun
• Optional external Balun allows tuning of random length, long wire or ladder line fed antennas
• Optional interfaces for Icom and Yaesu available
• Power requirements: 11 to 16 volts DC at 750 mA max during tuning
• Enclosure: 8.5D x 6.0W x 2.0H inches
• Weight: 2 pounds

The Z-100 Tuner:

• Microprocessor controlled
• High efficiency switched "L" tuning network
• LED indicators for Status and SWR
• 200 fast memories
• Latching relays, holds tune position forever
• Optimized, low power consumption tuning algorithm
• Tuning time: 0.5 to 6 seconds, 3.0 average
• Current consumption: Idle - Nearly zero amps. Tuning - 300 mA max
• Voltage requirements: 11 to 18 volts
• 1.8 to 54.0 MHz coverage
• Tunes 6 to 800 ohm loads, 10:1 SWR (3:1 SWR on 6 meters
• Power range: 0.1 to 125 watts (50 watts on 6 meters
• For Dipoles, Verticals, Vees, Beams and Coax Fed Antennas
• Optional external Balun allows tuning of random length, long wire or ladder line fed antennas
• Enclosure size: 5.5"D x 5.25"W x 1.5"H
• Weight: 14 oz

The Z-11Pro Tuner:

• 0.1 to 125 watt power range (SSB and CW), 100W on 6M
• Easy to read LED display for SWR and status
• 8000 3-D memories for instantaneous band changing
• Tuning time: 0.1 to 6 seconds full tune, 0.1 seconds memory tune
• Selectable user parameters: Auto/Semi, threshold, and more
• 1.8 to 54.0 MHz coverage. Built-in frequency sensor
• Tunes 6 to 1000 ohm loads (16 to 150 on 6M), 6 to 4000 ohms with optional 4:1 Balun
• For Dipoles, Verticals, Vs, Beams or and Coax Fed Antenna
• Optional external Balun allows tuning of random length, long wire or ladder line fed antennas
• Optional interfaces for Icom and Yaesu available
• Power requirements: 11 to 16 volts DC at 300 mA Max. 25 uA standby current
• User installable 8-AA or 8-AAA battery holder
• Small Size Enclosure: 7.7L x 5.0W x 1.5H. Weight: 1.5 pounds
• Not for use with FT-857(D) or FT-897(D) if you plan to use VHF or UHF. Use the AT-100Pro instead




The New FT Meter:


• Receive Mode: S-Meter, Discriminator or Voltage
• Transmit Mode: RF Power, SWR, Modulation, ALC or Voltage
• Cable length 3 feet
• Sensitive 500 uA meter movement
• Externally powered cool blue backlighting
• On/Off switch for backlight
• Backlighting requires 11 to 15 volts, 100 mA
• Size: 3.6W x 3.0 D x 2.6H inches
• Weight: 0.5 lb.
• For use with FT-857(D) and FT-897(D) only